From maintenance to training, these 10 tips will help you fine-tune your ECS and concentrate on growing a successful crop.
An integrated environmental control system (ECS) is the best tool you can have for making science-based growing decisions, hands down. Integrating all your equipment under one system, not just your temperature and humidity controllers, but also lighting, water treatment, irrigation, CO2 enrichment systems and alarms, provides better data, tighter control, increased energy savings and reduced waste.
Some systems will analyze your harvest statistics and record labor tasks to improve productivity. Such systems use anticipatory logic to make predictive changes to your climate, particularly important in a dynamic greenhouse environment where sunlight changes every few minutes on a partly cloudy day. This allows you to focus on growing your crop rather than worrying about your climate. For example, whereas non-integrated equipment may require several adjustments per day as conditions change, the greenhouse that my team managed only needed adjustment seasonally (four times per year).
ECSs store and display data to allow you to fine-tune your programming. They warn you when things go wrong via audible alarms and call-out texts, emails or phone calls. Lastly, with experience, a grower can learn to diagnose equipment problems using data graphs, often long before an alarm condition is reached. Because of their capacity to amplify the skills of a good grower, I recommend to my colleagues that they invest in the best ECS system they can afford.
Here are some tips on getting the most out this vital tool:
Too often, even though you were offered a certain number of hours of free training on your system, in the rush and excitement of starting a new facility, this training gets dropped. This is true especially when you realize just how little daily input these systems require. Other times the vendor may not voluntarily provide it unless you insist. Put this training on the calendar, tell everyone of its importance and try not to be interrupted during it.
When lightning struck my ECSs outdoor weather station, the charge traveled down the wires to the individual greenhouse controller that the weather station was wired to and fried it. Luckily, the charge did not travel further upstream destroying others, as a fail-safe was built in. Inexpensive communication chips were designed to fail when overloaded, protecting the boards of other controllers.
When designing your system, have at least one spare standard electrical outlet controlled by the ECS. This will allow you to quickly add equipment later, such as an extra dehumidifier, or maybe something that hasn’t even been invented yet.
Create a maintenance plan and assign responsibilities to it. If the fans that aspirate your sensor boxes fail, the sensors will measure higher than the room temperature when the lights or sun heat up the box. If your system uses wet wicks to measure humidity and those wicks go dry or get covered in a biofilm, they will measure incorrectly. Grime on glass thermistors that measure temperature/relative humidity (RH) affects the reading. Weather stations need to be calibrated and checked; I once had rain get inside a supposedly sealed electronics board for an outdoor humidity probe, causing inaccurate readings.
When some temperature probes fail and the signal is lost, they often cause an alarm condition reading such as -40° C, which allows you to know exactly when it happens. However, many times I observed that the sensor reading just froze at the last measurement and the room continued heating or cooling as it was at that moment, until it was too hot or too cold and there was no alarm! For this reason, I chose to replace my sensors every two years, even though they rarely, if ever, needed calibration until the day they stopped working.
When working on circuit boards, such as wiring in new sensors or changing chips for a software upgrade, always wear a static discharge band around your wrist and have it attached to a ground in the cabinet. Without this protection for the equipment, you may not even see or feel the static spark, but the resultant “ghost in the machine” damage is hard to troubleshoot.
Understand what normal looks like, so you can better understand abnormal. You may think that troubleshooting problems is all about observing the actual equipment, but some problems only arise under certain weather conditions, which are hard to replicate. Some problems happen invisibly, such as when a heating valve at my facility was malfunctioning. It never resulted in an alarm condition, and it’s unlikely that a human could have observed or felt it, but the temperature was being controlled poorly.
When there is a malfunction, print a copy of the graph, label what the problem was and how it was resolved, and create a troubleshooting binder. Until I learned to do this, I would find myself looking at a graph and knowing I had seen that problem before, but I couldn’t remember what it was.
The true power of integrated controls is the fine-tuning of the environment. With an understanding of programming and close observation of climate data, you will be amazed at what you can achieve. We had a researcher doing important supplemental lighting research, requiring the same daily light integral, or accumulated light, in the greenhouse across all seasons and weather patterns in our Midwestern U.S. location, where it naturally varied from 2 mols/m2/day to 50 mols/m2/day. By using two layers of shade curtains and smart control of lights, we were able to “dial in” a DLI of 12 each day with an error of just less than 2 mols/m2/day.
By properly understanding how the climate affects plant physiology, growers can use data from an ECS to fine-tune optimum environments or even apply controlled stresses to achieve their production goals. Similar conditions can be maintained crop after crop, season upon season, for the predictability and uniformity of plant attributes. Graphical tracking and user expertise allow for troubleshooting and repair of mechanical or programming errors that might linger for weeks or months with no one the wiser. The anticipatory logic and fast cycling capability of these systems is quite literally the difference between responding to environmental conditions and creating those conditions.
Rob Eddy is a greenhouse consultant and owner of CEA Consultancy based in West Lafayette, Indiana; robeddy92@gmail.com.